Author Topic: New problem cropped up  (Read 32415 times)

Josephbw

  • Conductor
  • ****
  • Posts: 251
New problem cropped up
« on: May 03, 2016, 07:36:43 PM »
I MU'd 2 engines together to test that function, and everything went OK until I started them around my test loop. My No. 1 engine was pulling No.2 and they seemed to be fighting each other. So then I got another engine (No. 3), and paired it with No. 1, and it was a little better matchup, but No.1 was still trying to pull away from No. 3 also. All 3 engines have had the full load current test done at initial setup.

Just for kicks I tried to MU all 3 engines together, but that didn't happen, I got the error message "Maximum number of locomotives are in use" when I tried to select the 3rd engine for the consist.

Then I redid the load current test and these are the same results (within a few mA's) as I had originally. No. 1 was 330mA, No.2 was 560mA, No.3 was 530 mA. These are all three brand new Atlas engines with less than 30 minutes on each one.

It's apparent that I'm going to have to adjust the acceleration and speed for at least two of them. But my question is, is there a limit on how much power the engines can draw in a consist? I was approaching 1-1/2 amps with this combo.

Thanks, Joe

Alan

  • Conductor
  • ****
  • Posts: 1073
    • LK&O Railroad
Re: New problem cropped up
« Reply #1 on: May 03, 2016, 07:52:39 PM »
Try breaking in the locos by themselves real good before consisting. New locos need some time on the rails for the brushes to seat well and the gear sets to smooth out. I wouldn't be surprised to see the two 500mA engines come down as they get some track miles on them.

For the second part, electrical draw of the total consist is limited only by your power supply's ability to provide sufficient voltage/amperage (wattage) and your wiring to get it there (minimum voltage drop). The modules don't care and are not affected by other locos power needs.
Alan

LK&O Railroad website

When I was a kid... no wait, I still do that. HO, 28x32, double deck, 1969, RailPro

G8B4Life

  • Signalman (Global Mod)
  • Conductor
  • *****
  • Posts: 1237
  • I'll think of a catchy tag line one day
Re: New problem cropped up
« Reply #2 on: May 03, 2016, 11:59:08 PM »
Are your modules and controller up to date with the latest software?  RP can control 6 locomotives at once, singularly or MU'd so it seems strange to see that message, unless you had another MU operating which it doesn't sound like you did.

I'd also try letting the loco's run by themselves for a while as well. Because our models are not examples of fine precision mechanical engineering we usually do have to wear them out a bit first to bed them in.

It may also be just plain that the loco's don't like working together (even real one's have this problem sometimes). Like speed matching I believe that RP's load sharing can only go so far to compensate for characteristics like motor speed and gear ratios; too far different and load sharing probably won't work as well as expected. Adjusting the acceleration and speed might have to be done.

- Tim

KPack

  • Conductor
  • ****
  • Posts: 784
Re: New problem cropped up
« Reply #3 on: May 04, 2016, 12:22:50 AM »
As stated, run the locomotives first forwards and backwards for a while to break them in.  500 mah for an Atlas seems high to me.  Most of my Atlas locos are down in the 300's, with one or two around 200.

As far as the maximum locos, I wonder if you had another active consist that you weren't aware of?  I don't know if having other locos consisted but not actively controlled makes a difference.  Never really tested that.  Un-MU everything and try it again.

I have two locomotives that are a bit more picky when it comes to MU'ing.  Even Railpro has it's limitations of what can be done within the bounds of model locomotives.  However, there are ways to help with these rare outliers.  One of my 'problem' locomotives was actually an Atlas that runs incredibly smooth and draws very little current.  It liked to push/pull other locomotives around.  The fix was to artificially set the full load current.  To do this you open the full motor load current setting, then when it asks to set it automatically select "no".  You will then be able to move the full motor load current setting using the wheel to whatever you want.  In this case I raised the load current higher, to be closer to what most of my other locomotives are.  Works much better now with no pulling/pushing.  I haven't seen any deleterious effects of manually adjusting the load current.

The other locomotive is a highly modified Athearn with a Kato drive which doesn't quite fit perfectly with the athearn drivetrain.  To get it to work I had to put more pressure on the athearn dogbones, which increased the total resistance in the drivetrain.  The motor runs smoothly, so it seemed to give a lower reading on the automatic load current set than what it actually was.  It would run great with an indentically modified locomotive, but then with others it struggled (was drug around when it was the follower).  Artificially adjusting the full motor load current to a higher setting solved the problem.  I believe the higher setting is more accurate for that locomotive, based on the increased resistance in the drivetrain.

Try it out and see if that solves your problem.

-Kevin

Antoine L.

  • Engineer
  • ***
  • Posts: 52
Re: New problem cropped up
« Reply #4 on: May 04, 2016, 09:27:48 AM »
I have had the same problem as the OP.
Seems like now I don't have it.

It felt really "random" at that moment.

Antoine

Modeling a mix of CN / Wisconsin central on a 12x15 freelance area.

Josephbw

  • Conductor
  • ****
  • Posts: 251
Re: New problem cropped up
« Reply #5 on: May 04, 2016, 09:56:14 AM »
Thanks guys, I appreciate the feedback. Yesterday wasn't a good day. I was working on my paint booth and managed to shoot a 1-1/4" brad into my finger with my pneumatic nail gun. It's all swollen up and throbbing and kept me up a lot last night. I still have to do a lot of cleanup in preparation for the arrival of my brother and his 2 boys Friday. He'll be here for about a week so I may not have the time to work in the basement for a while. When I do get the time, I'll let you know the outcome.

Thanks again,
Joe

PS. it sucks getting old, forgetful, and clumsy.  :(

nodcc4me

  • Conductor
  • ****
  • Posts: 688
  • RailPro Fan
Re: New problem cropped up
« Reply #6 on: May 04, 2016, 12:27:29 PM »

PS. it sucks getting old, forgetful, and clumsy.  :(
Hey Joe, I resemble that.  ;D

Sorry to hear about your injury. That must have been extremely painful.

The only time I have had one engine pulling on another is when I forgot to set the direction of the second or third engine. I'm sure you thought of that, as it would be very apparent.
Al

Run your train, not your brain. Get RailPro. It's a no-brainer.

hirailer

  • Engineer
  • ***
  • Posts: 59
Re: New problem cropped up
« Reply #7 on: May 04, 2016, 03:46:44 PM »
Hope your injury heals soon. In my old age fumbling, Several years ago I ran a 1/8 drill bit into a finger. Not funny :-X

The first time I tried to link two locos together I had the same problem as you have. After messing with them for a while, I decided to run them independently for a while before linking them again. That seemed to do the trick as I have never had this problem since. Both locos were Atlas Yellow box GP-40's that were at least 25 years old but never had been run.

Mel
Having more fun with RailPro

Antoine L.

  • Engineer
  • ***
  • Posts: 52
Re: New problem cropped up
« Reply #8 on: May 16, 2016, 09:57:15 AM »
Hi

Problem re-occured yesterday, again with new locomotive in the consist. 2 Kato SD40, same gearing, same road number (I renumber one, don't worry) Basically, the same product. Both running à 290 MaH.

Symptoms: Jerky, one pulling more than the other. Vice versa. Slowing down, then back to speed with an acceleration surge. Once stopped and knob turned to 0,00%, one of the loco was still at 9% current, making it pull alone when direction switched, motor still humming after 0,00% got me intrigued so I checked and it was at 9%.  Then, all of a sudden, one of the other loco direction was "mixed up" When on forward, it would go backward, like if I had switched the gear direction, but obviously did not, and then, it automatically went back to normal.

Very odddddddd. I felt like losing control. Which is a no no no.

ideas?

Antoine



Modeling a mix of CN / Wisconsin central on a 12x15 freelance area.

G8B4Life

  • Signalman (Global Mod)
  • Conductor
  • *****
  • Posts: 1237
  • I'll think of a catchy tag line one day
Re: New problem cropped up
« Reply #9 on: May 16, 2016, 11:10:07 AM »
Antoine,

Just have to check, all the modules have the same version of the software in them (and HC software up to date)? I don't know if using different versions of the module software could cause issues like this but it's worth asking.

Your description of doing strange things suddenly almost sounds like something interfering with the signal and the module gets confused, though I see this as quite unlikely.  Might be an idea to set  the motor current to a higher value instead of using the auto reading on the new loco

This could be a Ring Engineering question unfortunately, especially with the unusual "reverse gearing". Never had that one here before.

- Tim

Antoine L.

  • Engineer
  • ***
  • Posts: 52
Re: New problem cropped up
« Reply #10 on: May 16, 2016, 01:10:03 PM »
Well, I think they're all LM-2S factory version. They are certainly not up to date for one main reasons. When I try to update them it says "programmer started" and then nothing happens. Can someone tell me how to update?

As for interference, Maybe the smart TV? the wireless phone? could it be dirt near the track (1/2 inch away?)(I use real sifted dirt, maybe it has tiny magnetic things in it...?, could it be that? I use woodland scenics ballast for track tho.) I have no cellphone.

The locos run fine when not consisted, very smooth.

Antoine



« Last Edit: May 16, 2016, 01:11:36 PM by Antoine L. »
Modeling a mix of CN / Wisconsin central on a 12x15 freelance area.

nodcc4me

  • Conductor
  • ****
  • Posts: 688
  • RailPro Fan
Re: New problem cropped up
« Reply #11 on: May 16, 2016, 06:56:20 PM »
Antoine, do you have any other locomotives that you can consist either of these two Katos with, one at a time and see if the problems persist? Although interference could possibly cause this erratic behavior, as Tim stated, it is unlikely because RP uses spread spectrum technology, which limits interference problems.

I'm also thinking a setting could have something to do with this. Try setting your acceleration, deceleration and start speed to default on both engines.
Al

Run your train, not your brain. Get RailPro. It's a no-brainer.

Alan

  • Conductor
  • ****
  • Posts: 1073
    • LK&O Railroad
Re: New problem cropped up
« Reply #12 on: May 16, 2016, 07:33:24 PM »
I'll mention this only because it happened to me and I was able to recreate the problem on demand.

Whenever a switch mode power supply was in, on nearly in, the direct line of sight between a loco and the controller I would lose control of the loco, it became a runaway. Just prior to losing control it would often act erratically speed-wise.

I had a loop of track setup to break in new locomotives. Originally I used a wall wart to power it. Everything was fine. Then I switched to a SMPS. It was positioned next to the loop. On occasion I would lose control. On one occasion I noticed the SMPS was directly between me and the loop. The loco lost control when it passed behind the SMPS. I moved over so the SMPS was not between me and the loop. No loss of control. I found that I could force loss of control by where I was standing relative to the SMPS. Why the RF signal cared whether or not the power supply was between the controller and the loco is beyond me but it most definitely did.

I know what you are thinking - was the power supply properly grounded? Yes.

Alan

LK&O Railroad website

When I was a kid... no wait, I still do that. HO, 28x32, double deck, 1969, RailPro

Josephbw

  • Conductor
  • ****
  • Posts: 251
Re: New problem cropped up - UPDATE
« Reply #13 on: May 16, 2016, 10:08:12 PM »
I sent an email to Tim Ring the other day and got a reply this morning in regards to the problem of "Maximum number of locomotives are in use". I received this response this morning.

Hi Joe,

I am sure there is nothing wrong with either HC.  You get a 'Max. locos in use' when your HC is actively controlling more than 12 locos.  Although you can have dozens of locos loaded in the HC you can only control up to 12 at a time with a single HC.  The HC automatically removes unused locos form the actively controlled list. However, to get the HC to automatically remove an unused loco it has to be at speed 0.0% for more than 10 seconds before you turn off the HC and the track power.  If you don't do this the loco can stay active in the HC active loco list and can eventually give you a 'Max. locos in use'.  To start from scratch you can press the reset button on the back of the HC that is reporting this (that will clear the locos in use list).  Then be sure before you turn the layout off to set all speeds to 0.0% and wait over 10 seconds before powering off the HC and layout.


Please let us know your results because we are very interested in happy customers.

Thank you for contacting Ring Engineering!


So apparently there is a 12 loco limit in a consist. There are a lot of gotcha's that should be included in the manual, and this is one of them. I will send a positive report back to Tim, and also a suggestion for a manual update. BTW, I did what was suggested and it works like a charm.  :) I have also been running the 3 unit consist together pulling 30 cars plus 2 dummy engines and a caboose around my test loop whenever I'm down in the basement where I can keep and eye on it. It does seem to be smoothing out and they are playing together much better now.

Joe

nodcc4me

  • Conductor
  • ****
  • Posts: 688
  • RailPro Fan
Re: New problem cropped up
« Reply #14 on: May 17, 2016, 07:37:12 AM »
I was not aware of the 10 second power-off delay Joe. Thanks for posting it. Glad you got your problem resolved.
Al

Run your train, not your brain. Get RailPro. It's a no-brainer.