Author Topic: New LM-4S-G?  (Read 14150 times)

G8B4Life

  • Signalman (Global Mod)
  • Conductor
  • *****
  • Posts: 1241
  • I'll think of a catchy tag line one day
New LM-4S-G?
« on: December 11, 2021, 07:48:57 AM »
This one hasn't made Ring's site yet, however the program for it appears as a download in RPA. While not a large scale modeller myself anyone have any details on it?

lm-4s-g program listing.png



- Tim

ron045

  • Engineer
  • ***
  • Posts: 70
Re: New LM-4S-G?
« Reply #1 on: December 11, 2021, 09:01:26 AM »
Following.

Gibs

  • Engineer
  • ***
  • Posts: 82
Re: New LM-4S-G?
« Reply #2 on: December 12, 2021, 07:20:49 PM »
Something else also of interest on the update section, my PWR-56 says it has Rev 1.11 installed yet only 1.10 is available to D/L!
Cya Down The Line.

William Brillinger

  • Dispatcher (Admin)
  • Conductor
  • *****
  • Posts: 1345
    • Precision Design Co.
Re: New LM-4S-G?
« Reply #3 on: January 10, 2022, 02:01:54 PM »
Official word from Ring Engineering on the LM-4S-G:

It is the same as LM-3S-G but has a operating voltage of 28 volts and absolute max of 30 volts (Higher than LM-3S-G). 
It has been tested to work on USA trains 10A and 4A power supplies.
- Bill Brillinger, RPUG Admin

Modeling the BNML in HO Scale, owner of Precision Design Co., and RailPro Dealer.


zr1rob

  • Fireman
  • **
  • Posts: 30
Re: New LM-4S-G?
« Reply #4 on: January 10, 2022, 05:17:09 PM »
28V is great news for battery guys like me. Now I can use a 6s LIPO and get some speed out of my low geared locos.

gregeusa

  • Engineer
  • ***
  • Posts: 98
    • Greg's web site
Re: New LM-4S-G?
« Reply #5 on: March 20, 2022, 02:49:00 PM »
Since I cannot find any specifications on the RailPro site, will tag onto this thread.

Is there any official published specification of the current handling of the LM-4S-G? constant current and "surge" or "stall" at least are needed.

It is very strange that this information is not readily available on the official web site, not even the working voltage.

Greg
Lots of tips and techniques on my site: www.elmassian.com contact me greg@elmassian.com

William Brillinger

  • Dispatcher (Admin)
  • Conductor
  • *****
  • Posts: 1345
    • Precision Design Co.
Re: New LM-4S-G?
« Reply #6 on: March 20, 2022, 03:18:41 PM »
you can find all the RailPro Manuals here: http://ringengineering.com/RailPro/Documents/

The manual for the LM-4S-g is also listed on the LM-4S-g page: http://ringengineering.com/LM-4S-G.htm
- Bill Brillinger, RPUG Admin

Modeling the BNML in HO Scale, owner of Precision Design Co., and RailPro Dealer.


gregeusa

  • Engineer
  • ***
  • Posts: 98
    • Greg's web site
Re: New LM-4S-G?
« Reply #7 on: March 20, 2022, 03:40:13 PM »
First, the most important and common specifications should be on the dang site.

Would you buy a car where you had to read the owners manual to find out the gas mileage?

But it indeed was in the manual... I keep forgetting to go to the lowest level on the web site, and then scroll and scroll to find the manual.

Specifications
Maximum Power Input Voltage: 28 Volts (Absolute Maximum voltage 30.0V)
Maximum Motor Stall Current: 8 Amps
Maximum Output Current on any Single Light Output: 500mA.
Maximum Output Current on all Light Outputs Combined: 500mA.
Audio Output Power: 13 Watts into a 4 ohm load. 7.4 Watts into an 8 ohm load

So, thanks.... wonder what the maximum continuous current is though?

SoundTraxx rates their stall current (which really needs a duration or it is meaningless) similarly, but can only handle about 3 amps continuous.

The continuous rating is much more important, no one runs their locos in STALL all the time (not for long ha ha!)

I guess I will have to rely on user feedback...

Thanks for the tip, I promise to dig more on the site next time.
Lots of tips and techniques on my site: www.elmassian.com contact me greg@elmassian.com