Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - William Brillinger

Pages: [1] 2 3 ... 71
RailPro Installations / Re: Caboose Lighting
« on: October 14, 2020, 06:16:38 AM »

If you have track power hooked to the leads, the HC should be able to find it. (hook it straight to the rails to test)
Is it possible that the LM-1 is still in the loco inventory on the HC under it's old name?

If you attached power to the wrong leads, then it will be burnt out. You may need to send it in for a $25 repair.

General Discussion / Re: Axle-hung motors
« on: October 10, 2020, 01:35:41 PM »
I note that the website says these are not available - I seem to recall it said that back in 2014 when I first saw them too. 

ULT is "Ultimate" it's a much higher quality sound file with more features and detail.

RailPro Discussion & Help / Re: Locked Control Screen
« on: October 04, 2020, 03:09:03 PM »
Looks like a failed screen. Contact Ring Engineering for repair.

I suggest using the phone before email. It's usually faster.

RailPro Discussion & Help / Re: PBM-2 Installation
« on: October 03, 2020, 02:42:19 PM »
My question: "Is the adapter board for the PBM to LM2 available?"

And Tim Ring's reply: "Not at this time. It is on our to do list."

RailPro Discussion & Help / Re: PBM-2 Installation
« on: October 01, 2020, 05:58:28 AM »
Good question - I'll check into this!

RailPro Discussion & Help / Re: Is it just me?
« on: September 18, 2020, 11:07:18 AM »
Traylor, I sent you an email. I'm sorry that this hasn't worked out well for you.

The most common cause of an unresponsive LM is a short in the installation that fries a component on the power input. Ring generally charges $25 to repair this. He say's it's easy to spot when this has happened when he opens it up.

Contact me and I'll be happy to do what I can to get you going or take the product back.

RailPro Discussion & Help / Re: LM-3S-G
« on: August 31, 2020, 10:05:15 AM »
That's great news!

RailPro Discussion & Help / Re: LM-3S-G
« on: August 28, 2020, 10:06:27 PM »
To start the installer, go to the folder where you saved it, and right click the file.
Then choose "run as administrator".

RailPro Discussion & Help / Re: LM-3S-G
« on: August 28, 2020, 06:12:43 PM »
When you ran the software, did you actually right click it and choose "run as administrator" ?

RailPro Discussion & Help / Re: grade crossing
« on: August 27, 2020, 07:10:15 AM »
press one button and have the locomotive automatically blow the correct sequence?  If that's what you're looking for, the answer is no.  That is not available on Railpro right now.  It could be added, but it's easy to blow the horn/whistle by pressing the button.

If you record your own custom horn sound you could do this. The "crossing" button would play the soundfile you create with the crossing pattern.

RailPro Discussion & Help / Re: LM-3S-G
« on: August 24, 2020, 06:43:20 AM »
Is it possible that it was shorted during the install and died when it received power?

I would remove it from the locomotive, connect it directly to the power and test.

If you still can't see it then I would contact Ring Engineering for assessment and repair.

New Users Start Here / Re: Introduce Yourself...
« on: August 13, 2020, 11:38:08 AM »
We have had a number of new members recently and I would like to take this opportunity to welcome all of you here!

RailPro Discussion & Help / Re: Low voltage warning
« on: August 01, 2020, 02:56:12 PM »
also, are you using a KA? or PBM? If a KA, what brand? (PBM is Ring's Keep Alive Product)

RailPro Discussion & Help / Re: Low voltage warning
« on: August 01, 2020, 11:39:18 AM »
what does the LM report for track voltage? does it agree?

Pages: [1] 2 3 ... 71