Author Topic: How To Setup Manual Notching  (Read 19979 times)

William Brillinger

  • Dispatcher (Admin)
  • Conductor
  • *****
  • Posts: 1342
    • Precision Design Co.
How To Setup Manual Notching
« on: July 21, 2016, 09:09:51 AM »
To Setup Manual Notching on RailPro follow these steps:

Program the Notch Up and Notch Down buttons as follows:
(You must use the Notch UP and Notch Down Images for the buttons.)

How to setup manual Notching on RailPro (1).JPG

How to setup manual Notching on RailPro (2).JPG

Set the Locomotive to use Manual Notching:

How to setup manual Notching on RailPro (3).JPG

Manual Notching should look like this on your screen main:

How to setup manual Notching on RailPro (4).JPG
- Bill Brillinger, RPUG Admin

Modeling the BNML in HO Scale, owner of Precision Design Co., and RailPro Dealer.


Josephbw

  • Conductor
  • ****
  • Posts: 251
Re: How To Setup Manual Notching
« Reply #1 on: July 21, 2016, 12:14:55 PM »
Hi Bill, what does your "Roll" button do?

Thanks, Joe

nodcc4me

  • Conductor
  • ****
  • Posts: 688
  • RailPro Fan
Re: How To Setup Manual Notching
« Reply #2 on: July 21, 2016, 12:15:52 PM »
Couldn't be any easier. Thanks Bill!  :)
Al

Run your train, not your brain. Get RailPro. It's a no-brainer.

William Brillinger

  • Dispatcher (Admin)
  • Conductor
  • *****
  • Posts: 1342
    • Precision Design Co.
Re: How To Setup Manual Notching
« Reply #3 on: July 21, 2016, 12:32:02 PM »
Quote
Hi Bill, what does your "Roll" button do?

The Roll and Squeal buttons are for recordings I made of a train rolling and Flange or Brake Squeal.
You can find the Squeal here: http://rpug.pdc.ca/index.php?topic=140.0

The Roll sound is not uploaded as I didn't think there was much interest in it.
You can hear it in this video:


They are fun, but could be better.
« Last Edit: July 21, 2016, 12:35:04 PM by William Brillinger »
- Bill Brillinger, RPUG Admin

Modeling the BNML in HO Scale, owner of Precision Design Co., and RailPro Dealer.


SD90

  • Fireman
  • **
  • Posts: 38
Re: How To Setup Manual Notching
« Reply #4 on: July 21, 2016, 06:00:19 PM »
Nice! I like the squeal and clank sounds!

William Brillinger

  • Dispatcher (Admin)
  • Conductor
  • *****
  • Posts: 1342
    • Precision Design Co.
Re: How To Setup Manual Notching
« Reply #5 on: July 21, 2016, 08:14:48 PM »
Thanks!  the Clanks can also be downloaded from the files section on this site.
- Bill Brillinger, RPUG Admin

Modeling the BNML in HO Scale, owner of Precision Design Co., and RailPro Dealer.


Josephbw

  • Conductor
  • ****
  • Posts: 251
Re: How To Setup Manual Notching
« Reply #6 on: July 22, 2016, 09:59:35 AM »
Thanks Bill, that adds another dimension to the layout experience.  ;D

Joe

Dean

  • Conductor
  • ****
  • Posts: 211
Re: How To Setup Manual Notching
« Reply #7 on: July 25, 2016, 12:35:36 PM »
Does the notching control the sounds, or does it control the throttle?

Thanks
Dean

nodcc4me

  • Conductor
  • ****
  • Posts: 688
  • RailPro Fan
Re: How To Setup Manual Notching
« Reply #8 on: July 25, 2016, 12:40:54 PM »
Notching does not control the throttle. The controller buttons control the notching effect.
Al

Run your train, not your brain. Get RailPro. It's a no-brainer.

Josephbw

  • Conductor
  • ****
  • Posts: 251
Re: How To Setup Manual Notching
« Reply #9 on: July 25, 2016, 01:04:57 PM »
The way I do it, is to notch up 1-3 notches, then gradually increase the throttle knob, then notch up as necessary, with the appropriate throttle response. Or you could adjust your momentum up, crank up the throttle, then notch up. There are several options on how to control it.

Joe

SD90

  • Fireman
  • **
  • Posts: 38
Re: How To Setup Manual Notching
« Reply #10 on: July 25, 2016, 03:27:17 PM »
Is this like LokSounds full throttle feature? Where you can increase the prime mover sound without actually increasing the speed of the locomotive? Making it sound as if the train is very heavy?

nodcc4me

  • Conductor
  • ****
  • Posts: 688
  • RailPro Fan
Re: How To Setup Manual Notching
« Reply #11 on: July 25, 2016, 03:33:08 PM »
I'm not familiar with the Loksound feature, but yes, the notching and throttle are independent of each other when using manual notching.
Al

Run your train, not your brain. Get RailPro. It's a no-brainer.

William Brillinger

  • Dispatcher (Admin)
  • Conductor
  • *****
  • Posts: 1342
    • Precision Design Co.
Re: How To Setup Manual Notching
« Reply #12 on: July 25, 2016, 03:40:07 PM »
The biggest difference is RailPro's manual notching vs Loksound's Full throttle control is that you never remove the ability to control the speed of the train from the knob. You can always control the train, and you can always control the prime mover sound.  But you cannot currently exit Manual Notching "on the fly" with RailPro, either you're using it, or you're not.
- Bill Brillinger, RPUG Admin

Modeling the BNML in HO Scale, owner of Precision Design Co., and RailPro Dealer.


SD90

  • Fireman
  • **
  • Posts: 38
Re: How To Setup Manual Notching
« Reply #13 on: July 25, 2016, 05:33:36 PM »
So you mean if you are using manual notching, the prime mover sound is controlled by you, not the throttle? And you just have to set it up on the throttle? This sounds like what I want!
Is there a video that shows this?
Thanks Bill!

William Brillinger

  • Dispatcher (Admin)
  • Conductor
  • *****
  • Posts: 1342
    • Precision Design Co.
Re: How To Setup Manual Notching
« Reply #14 on: July 25, 2016, 05:51:44 PM »
My RailPro custom sounds demo uses manual notching exclusively.

« Last Edit: July 25, 2016, 05:57:34 PM by William Brillinger »
- Bill Brillinger, RPUG Admin

Modeling the BNML in HO Scale, owner of Precision Design Co., and RailPro Dealer.